Mountain Bike Build

I have lots of mountain bike parts lying around so I thought I'd try to make a bike out of them. First I bolted the saddle to the seatpost clamp:

Next I installed the seatpost clamp and seatpost so the frame can be clamped in a stand (or just set upside down on my basement floor):

To install the cantilever brake arms, first grease the outside of the studs and then slide the arms on. I usually use the middle hole if there's more than one position for the spring to attach to, unless the spring tension is way too loose or tight:

 Screw in the mounting bolts to secure the brake arms, but don't overtighten them to avoid damaging the studs (it's a good idea to use threadlocker on these bolts, and they often come with it from the factory):

To install the bottom bracket, first grease the threads on the main piece and screw it in part way:

 

Next screw in the plastic spacer part way (no grease needed here):

 

Now you can torque down the main piece all the way. It has to be really tight:

Finally just snug down the plastic piece. It's only a spacer, and if you overtighten it then it will crack.

Now slide the cranks on:

And bolt them down. These need to be pretty tight as well:

 

Next I installed the derailleurs. The bike frame already had a Shimano Hyperglide chain installed and I don't have any replacement pins. I'll show you how to install the derailleurs without breaking the chain:

For the rear derailleur you just remove the tension pulley, then wrap the chain around the guide pulley. You might need to rotate the inner cage plate in order to slide the chain in:

 

 Position the chain as shown then reinstall the tension pulley:

Simple enough. The front derailleur is even easier. Once you remove the cage screw you just need to carefully spread the plates apart and slide the chain through:

Now reinstall the screw and you're set:

 

If your front derailleur has a rivet rather than a screw then you'll have to disconnect the chain to install it. Next I decided to install the fork (not the most efficient way of doing things I'll admit). First I cleaned and repacked the headset bearings with grease:

Next I slid the fork through and tightened the headset:

Once the headset was properly adjusted (no play, minimal turning resistance), I installed the handlebars and stem:

Then I installed the cassette onto the rear wheel and put the wheels on the bike:

Starting to look like a bike now. Now the fiddly stuff. To position your shifters and brake levers on the handlebar, hold the grips next to the bar to find the right position for the levers:

Once you tighten the levers down you can start installing the cables. On these Rapidfire shifters you need to put the shifter into the slackest position (gear 7 on the right, gear 1 on the left), then slide the cable through the hole:

For the brake cables you will need to hook the barrel end into the brake lever, then slide the cable through the lever. These have a slot running through them that makes this so much easier:

Now cut the housing pieces to the right lengths and slide the cables through them. Oil the cable before threading it through the housings. Finally bolt the brake cables to the brake arms:

 

And bolt the shift cables to the derailleurs:

Now you have to adjust the cables. There are barrel adjusters on the brake levers, shifters, and the headset bracket for putting the optimum tension on the cables:

 

Adjusting indexed derailleurs can be a little tricky. First make sure the limit screws are correctly adjusted. For the rear derailleur you should adjust the cable so that the guide pulley is centered underneath each selected gear. If the shifting is still hesitant then you can make further adjustments with the barrel adjuster. On an indexed front derailleur, the barrel adjuster only really works for the middle gear. Try to adjust the cable so that the chain doesn't rub the derailleur cage when the chain is in either the lowest or highest gear in the back. This takes a bit of experience so good luck. Brakes are easier, just unscrew the adjuster until the lever feels nice and firm, and center the brake arms so that they don't rub the rim (cantilever brake pad adjustment).

Once everything is assembled correctly you can install the grips. I like to use hair spray. It gets pretty sticky once it's dry, and it'll lock the grips in place:

Here's the bike I ended up with. The fork I picked out was meant for 700c wheels, so I tried a road bike wheel in order for the brakes to reach the rim.

Is this a 76er? (Edit - I installed a short reach single pivot brake caliper on the rear and built another road bike wheel to match the front. It rides well as a hybrid).